BCD ACCESSORIES

One pair of medium weight pockets.  Each pocket has a Fastex Clip and holds approximately 5 pounds of lead. 

Colors available: Red, Orange, Yellow, Lime Green, Blue, Purple, Pink, Camo, Blue Camo, Pink Camo, Black

Small Mesh Weight Pockets that come in a pair. Can be easily and quickly be attached to the chest harness to act as trim weights. Soft lead weight is not included. 

The X-Pocket is secured to your harness on the waist belt and the length is adjusted and then attached to your leg with Velco, It is a large pocket and has a dring on the outside to clip off a spool or reel.

The Sausage Weight Pocket was designed to remove weight from your weight belt by securing it on the inside of your backplate . It is secured with bolts that attach your plate to a STA. If not using a STA, you can use Sex Nuts/Bolts. Lead shot is used as weight and is not included. 

Two sections with nuts, bolts and washers. 

A single Cam Buckle in stainless steel with StrapFriction pad on strap to hold tanks and keep them from slipping

• Two Inch webbing
• Friction pad sewn in
• Approximately 9 ounces

NOTE:  Straps are also available in chemical resistant webbing.

A single Cam Buckle in composite/plastic with StrapFriction pad on strap to hold tanks and keep them from slipping

• Two Inch webbing
• Friction pad sewn in
• Approximately 5.5 ounces

OxyCheq Stainless Steel Belt Buckle

Shoulder Harness Pads are designed to work with any Hogathian Harness System. They add padding to the harness shoulder straps and are easily attached to the webbing and backplate. Available colors:  Red, Orange, Yellow, Lime Green, Blue, Purple, Pink, Camo, Blue Camo, Pink Camo, Black

The Crotch Strap includes 2 inch wide (50mm) soft webbing, closed sewn loop on one end with straight D and a keeper and open end on the other. The advantage of having the front loop stitched keeps the from creeping or slipping when scootering. The webbing is soft and without resin; this helps to reduce excess wear on exposure suits. Our crotch strap is also available with a low profile D-ring. 

The Universal Crotch Strap is perfect for scootering and everyday diving. The three point system that eliminates contact, pressure or discomfort on sensitive areas of the body (crotch) for both men and women. 

The soft 2" crotch strap has a sewn in d-ring and includes a keeper that allows you to attach the strap to a backplate.

Quick Straps allow you to quickly and easily adjust your Hogarthian Harness. It is similar to the time tested Ultra Lite Plate design. Now, you can tighten your harness with ease and save a lot of time. 

The Medium Plate Pad fits the OxyCheq Medium SS and Aluminum Plates. It has a lift bag pocket and Zip ties to plate. Zip ties included.

 With continuous weave harnesses, it can often be difficult to tighten the shoulders by pulling on the waist straps. This is due to friction caused by the tortuous path that the webbing makes as it goes through the dual slots in the backplate. The Slide Bars mount on the back of the plate, between the slots. The slick, rounded surface minimizes the friction and makes the waist straps easier to pull through. 

• Attach various accessories, such as mesh carry pouch to plate
• One complete set, male & female
• Stainless steel, non-rusting construction
• Will pass through 3/8 in (9.5 mm) hole
• Includes friction O-rings

• Strong, durable alternative to traditional wingnuts
• Knurled gripping surface for easier disassembly
• Available in two thread sizes:
  
  • 3/8 in (9.5 mm) - fits Highland bands hardware SB725
  • 5/16 in (8 mm) - fits Highland bands hardware SB800

Add comfort and protect your exposure suit, by covering your web harness shoulder straps with these Highland shoulder pads.

• Made from quality 5 mm neoprene
• Simply slide over 2 in (50 mm) webbing
• Glued and stitched
• Seams reinforced with bar tack stitching

• 304 stainless steel harness buckle
• Designed to fit 2 in (50 mm) diameter webbing
• Positive cam lock
• Solid hinge pin

• Built from 54 in (137 cm) of 2 in (50 mm) harness webbing
• Rivet construction for maximum durability
• Included with Tec/Rec Harness (p/n HL803)
• Includes front and back D-rings and size adjuster

• Built from 1.5 in (38 mm) webbing - 11 in (280 mm) long
• 2 x 4 in (5 x 10 cm) SS sliders for extreme durability
• 4 SS rivets hold everything together
• Includes 2 serrated stays to accommodate thinner webbing and 2 D-rings for attachment points

• Full size weight pocket to add lead weights to a diving harness
• Load weights from the top zipper
• Uses the single-pull Catch n’ Release™ dump mechanism
• Attaches to 2 in (50 mm) webbing
• Each pocket holds up to 15 lbs (7 kg) of lead weights
• Sold as a pair

• Large, side-squeeze 2 in (50 mm) buckles on the front of the pocket for easy release of weights
• Adjustment strap with D-ring to cinch down for snug fit
• Each pocket holds up to 12 lbs (5.5 kg) of lead weights
• The dual grommet tail on the back allows for attachment to the backplate. This keeps pouches from sliding forward
• A 30º angled web retainer on the back provides an option to mount the weights at an upward angle, a feature desirable to small waisted divers
• Book screws not included

Use these plastic book screws for a wide range of applications, such as joining a single cylinder plate and wing when a single tank adapter will not be used.

• Will pass through 3/8 in (9.5 mm) hole
• Non-corrosive, durable plastic material for long life
• Includes 4 complete sets

Highland Weight Plates are a quick and easy way to add blocks of lead to a 2 in (50mm) wide piece of webbing such as a harness or weight belt. This will allow for fine tuning of your weight requirement without having to do any disassembly.

• Includes 2 plates and 4 pieces of green bungee
• Plate is molded from rugged glass-filled nylon for maximum durability
• Recommended for 1, 2, 3 and 4 lb blocks of lead
• Numerous pyramid anchor points bite into the webbing to keep the plate securely in place

• Designed to add up to 5 lbs (2.25 kg) of bagged shot or hard weight
• Attaches by sliding over the end of 2 in (50 mm) webbing
• Easy addition to tank band, weight belt or other harness systems
• Perfect for adjusting your trim in the water
• Available in two colors

• Same design as Single Weight Pocket (p/n WB101), except:
  
  • Allows excess webbing from tank cam strap to attach to hook-and-loop on front of weight pocket
  • Keeps cam strap webbing secure against cylinder
• Designed to add up to 5 lbs (2.25 kg) of bagged shot or hard weight
• Easy addition to XS Scuba weight belts or other harness systems
• Perfect for adjusting your trim

• Hook-and-loop release weight dump - pull out, then down
• Designed to add up to 5 lbs (2.25 kg) of bagged shot or hard weight
• Attaches by sliding over the end of any 2 in (50 mm) webbing
• Easy addition to XS Scuba weight belts or other harness systems
• Perfect for adjusting your trim

• Designed for adjusting your trim when using double cylinders
• Attach with lower cylinder band bolt
• Two stainless steel grommets for attachment
• Sealed opening with double hook-and-loop closure
• Holds up to 6 lbs (2.7 kg) of #5 or smaller lead shot
• Wide opening allows the use of hard weight up to 5 lbs (2.25 kg)